diff --git a/.gitignore b/.gitignore
index c9490a5..4fdc1bc 100644
--- a/.gitignore
+++ b/.gitignore
@@ -1 +1,2 @@
 /site
+orig/
diff --git a/docs/case2.0/img/voc-case2_0-case_b-comp.jpeg b/docs/case2.0/img/voc-case2_0-case_b-comp.jpeg
new file mode 100644
index 0000000..80d3b67
Binary files /dev/null and b/docs/case2.0/img/voc-case2_0-case_b-comp.jpeg differ
diff --git a/docs/case2.0/img/voc-case2_0-tripod-comp.jpg b/docs/case2.0/img/voc-case2_0-tripod-comp.jpg
new file mode 100644
index 0000000..3928b82
Binary files /dev/null and b/docs/case2.0/img/voc-case2_0-tripod-comp.jpg differ
diff --git a/docs/case2.0/packing.md b/docs/case2.0/packing.md
new file mode 100644
index 0000000..90b649c
--- /dev/null
+++ b/docs/case2.0/packing.md
@@ -0,0 +1,51 @@
+---
+title: Packing Guide
+---
+
+Packing the cases shouldn't be too complicated, but a few details need special attention.
+
+## Case x.1
+Compartments (from left to right):
+
+- **Power cables**: Schuko extension cords, power strips, schuko to TRUE1, schuko to C13, cable mats
+- **Accessories (back tower)**: Intercom crate, ethernet crate, audio and DI crate
+- **Accessories (front tower)**: Batteries and lucky cat crate, tape crate, embedder and converters crate
+- **Accessories (sorting box)**: Small adapters box
+- **Camera**: Tally crate, Mixer laptop crate, Camera crate
+- **XLR Cables**: Multiple XLR cables and Headphones (in a bag)
+- **Video Cables**: Multiple SDI and HDMI cables
+
+![](img/voc-case2_0-case_b-comp.jpeg) <!-- TODO: get a better image -->
+
+### Fitting the Tripod
+!!! info ""
+    Put all dampers (pan, tilt, counterweight) on zero and loosen the breaks before storing the tripod in the bag.
+    This way, everything can move to fit snugly.
+
+![](img/voc-case2_0-tripod-comp.jpg){ align="right", width="250" }
+The carrying bag of the new Sachter Ace M Mk II tripods got bigger than the old generation which means that the space in the case is quite tight.
+
+To make everything fit, place the tripod with the head to the right and carrying handle to the back (so it gets past the wooden compartment board).
+Otherwise the case lid may not close without forcing it.
+
+Please also take care of the remote control and place it on top and away from the front edge of the case so that it can't be jammed when closing the lid.
+There should be enough space between the legs of the tripod.
+
+### Fitting the Power Cables
+It's recommended to put the rubber cable mats in the compartment first, then the long cables and the power strips on top.
+
+
+## Case x.2
+Compartments (from left to right):
+
+- **FOH module** (bottom side to the left)
+- **Supplies**: c3lingo (currently only a placeholder) crate, office crate, minion crate, microphones crate
+- **ethernet compartment**: Multiple long ethernet cables
+- **Lectern module** (bottom side to the left)
+- **Encoder module** (bottom side to the left)
+
+<!-- TODO: get a picture showing the modules inside the case -->
+
+!!! info ""
+    Place all modules with the bottom to the left.
+    This way everything is "upright" when the case is loaded on the pallet.
diff --git a/docs/case2.0/tips-and-tricks.md b/docs/case2.0/tips-and-tricks.md
index 94239a1..bd0e96b 100644
--- a/docs/case2.0/tips-and-tricks.md
+++ b/docs/case2.0/tips-and-tricks.md
@@ -39,3 +39,8 @@ In case you need to reach the additional ports (HDMI and secondary SDI) of the U
 - Pull tray out until stoppers are reached
 - Place your hands with 4 fingers below the tray and the thumb on top ![](img/lectern-tray-stoppers_hands-comp.jpeg)
 - Press up next to the cable tie stopper until it goes past the I/O panel below ![](img/lectern-tray-stoppers-comp.jpeg)
+
+## FOH Module
+
+### Audio Mixer Setup is Funny
+- Grab the default scene from [the c3voc wiki](https://c3voc.de/wiki/hardware_ah-cq18t), put in on a USB stick and load to the mixer