Case 2.0: Add buildup guide

docs/case2.0/buildup.md

@@ -2,4 +2,101 @@
 title: Buildup Plan
 ---
 
-See <https://github.com/voc/checklists/blob/main/source/buildup.pdf>
+This guide will only cover the "physical" buildup and not how to apply the [configuration management](https://github.com/voc/cm/tree/master/bundlewrap).
+
+## Preparation
+Before you start carrying things around in the room, please determine the following things:
+
+- Where are the projector input and audio inputs located?
+- Where is the network uplink located?
+- Where are the emergency exits?
+- Where are power outlets?
+- Where is a good place for the FOH position (camera, FOH module and mixer laptop)?
+    * shall have a good view of the stage
+    * cables shall not create trip hazards in emergency exits
+
+## Buildup
+With these questions in mind, you can start distributing the eqipment.
+
+### Stage
+- Take the following items to the stage:
+    * lectern module
+    * 1 Schuko to TRUE1 cable
+    * 2 HDMI cables (one for projector, 3m for speaker laptop)
+    * 1 3m Cinch to 3.5mm jack cable
+    * speaker adapters crate/ bag
+    * battery charger crate
+    * microphone crate(s)
+- Place the lectern module somewhere convenient on its bottom or side (not on the back b/c of spilled drinks)
+- Connect to power and projector
+- Connect HDMI and 3.5mm jack cable and place on lectern
+- Start charging the first batch of batteries
+
+!!! info ""
+    Do not turn on microphones until a frequency scan was made
+
+### FOH/ Camera
+At small events we usually place the camera right next to the FOH and video mixer position so that the setup can be operated by a single person just in case.
+If we're sure that enough helpers are present, the camera can also be placed somewhere else.
+
+- Take the following items to the FOH position:
+    * FOH module
+    * 1 Schuko to TRUE1 cable + schuko extension cord, if needed
+    * Mixer laptop crate
+    * Headphones (DT 770)
+    * Encoder module
+    * 1 Schuko to C13 cable (aka "Kaltgerätekabel")
+    * 2 1.5m ethernet cables
+    * 1 2m SDI cable
+- Place the FOH module on a desk and the mixer laptop next to it
+- Connect FOH module to power (use extension cord, if needed)
+- Power the encoder from the FOH module, connect SDI and ethernet to FOH module
+    * FOH "SDI out" to Encoder "Slides"
+    * Ethernet to any "VOC" port
+- Place mixer laptop, connect power and ethernet to FOH module
+- If power supply is properly laid down, power up the FOH module, laptop and encoder
+- Load the default scene on the audio mixer
+
+For the camera:
+
+- Take the following items to the FOH position:
+    * Tripod
+    * Camera crate
+    * 1 2m HDMI cable
+    * 1 3-way power strip
+    * 2 XLR cables (long enough to reach FOH module)
+    * 1 SDI cable (long enough to reach FOH module)
+    * 1 ethernet cable (long enough to reach FOH module)
+- Setup tripod
+- Mount preview monitor on tripod
+- Place camera on tripod
+- Connect devices to power
+- Connect camera to preview monitor
+- Connect to FOH module with XLR (Aux 1+2) and ethernet (any "VOC" port)
+- Connect SDI to encoder ("Cam 1" input)
+
+### Cabling Between FOH and Stage
+To finish the setup, we need to connect the Lectern and FOH modules:
+
+- 1 SDI cable between lectern "Slides" output and FOH "SDI in"
+- 1 ethernet cable between lectern "trunk" port and FOH switch port 24
+
+The following steps are depending on the room:
+
+- Connect the **main mix** of the audio mixer at the FOH module with the audio input of the room using 2 XLR cables as well as DI boxes if needed
+- Connect to the house network:
+    * if a VOC VLAN exists: Connect a "VOC" port of the lectern module **or** the FOH module to the locations's network
+    * if no VOC VLAN exists:
+        + Connect a "public" port of the lectern module **or** the FOH module to the locations's network
+        + connect the router's "WAN" port to a "public" switch port on the FOH switch and any of the router's LAN ports to any "VOC" port on the FOH switch
+
+Also see the [cabling plan](cabling.md) for a detailed view of the signal paths.
+
+## Configuration
+To finish setting up the lecture room:
+
+- Test if internet is reachable
+- Apply the [configuration management](https://github.com/voc/cm/tree/master/bundlewrap)
+- Run a frequency scan using Shure Wireless Workbench
+- Assign frequencies
+- Check video and audio inputs, see [daily stage bootup](../checklists/avtech-daily.md)

docs/case2.0/cabling.md

@@ -0,0 +1,5 @@
+---
+title: Cabling
+---
+
+See [wiki](https://c3voc.de/wiki/_detail/hardware:voc-case2_0-wiring.png)